Product FAQs
ADD5930
What is the rated inlet water pressure?
The rated inlet water pressure is 0-9 PSI/0.06Mpa.
How long should I replace the filter? How to replace?
The suggested replacement cycle is 1 year. The exact filter replacement time is different according to the local water quality.
Why does the red light indicator still light up constantly after I replace the filter?
After installing the new filter, you need to reset the filter lifetime: Long press the water dispense button for 8 second to reset. Then flush the new filter.
Why does the appliance not work after pressing the water dispense button?
-Does the floating tablet in the water reservoir float up?
Take off the silicone sealing cap, then clean up the clogged floating tablet rail and floating tablet.
-Does input water level goes below the cylinder inthe water reservoir
Discard the remaining water left in the tank and refill it to the MAX line for the next cycle!
-Is the water reservoir stably placed on the water reservoir base?
Lift up the water reservoir, and place it back onto the water reservoir base.
Has the filter replacement cycle passed?
Check the filterlifetime indicator, and then do the flushing process again if necessary.
When I descale the water dispenser, what kind of solution to use?
It is suggested to use the food grade citric acid.
Can I wash the parts in the dishwasher?
Do not wash any removable parts in the dishwasher.
Remove the water reservoir, the lid, and the drip tray, and wash them with mild detergent and dry thoroughly.
When does the machine need to operate the flushing process?
The flushing process is necessary when the machine is set up before the first time use and after replacing the new filter.
Why does the water flow get slower than before?
1. The input water temperature is too low or too high. The rated input water temperature is 41-100℉/5-38℃. Too low or too high will influence the water flow.
2. Limescale can clog up the appliance and disrupt water flow. lf you startexperiencing slow water flow, it is time to descale the appliance. Please follow the guideline to descale.
3. Other parts damage. Please contact the after-sales service.
ADD6926
Where does the drain water go?
The RO water dispenser is equipped with a drain water backflow device, and an baffle in the raw water tank. Drain water would flow back to the raw water tank. So don't worry about it. At the same time, the dispenser will remind you to change water according to the water quality in the water tank, which is convenient and smart! There is a baffle in the middle, which can separate the drain water and raw water.
Too much drain water
Dear customer, the drain water ratio is 3:1, which means 3 cups of pure water will have 1 cup of waste water. At present, all reverse osmosis pure water dispenser on the market all produce drain water. The water production rate of our water dispenser is in line with the national grade A level of water efficiency standard, which is very water-saving.
Water dispenser leakage/leakage from the bottom
Dear, if this ADD6926 machine is leaking water, please check the following two points:
1. Take out the raw water tank and check whether the water tank leaks
2. Check whether the drip tray is full, leads to water leakage.
PS: After the investigation, you can talk to us about the investigation situation. We will solve it for you.
Why does the exchanging water indicator flash when there is water in the water tank?
Hello! The changing water reminding of this dispenser relies on the white float in the water tank to sense the water level switch to remind changing water. If the white float is stuck and does not float up or has no magnetism, it may cause changing water reminder. Another reason is that there is another magnetic sensor on the water tank cover. If the magnetic sensor on the water tank cover cannot be detected, a changing water reminder will also appear. It can be verified by a magnet.
Need to replace water frequently
Usually under the following situations, this ADD6926 water dispenser reminds you to change the water:
①The water level of the raw water tank reaches or is lower than the minimum water level;
②The TDS value of raw water is high
③If the water in the raw water tank has not been changed for more than 48 hours, the machine cannot produce water.
PS: Every time you change the water, you need to pour out the drain water in the raw water tank, and then fill the raw water tank with water and put it back on the machine and cover it. Otherwise the machine will remind you to change water more often.
Why does the water dispenser take a long time to produce water?
Hello! This machine normally produces water for about 10-15 minutes. If it exceeds this period, it may be that the filter has been used for too long or the water quality is too poor to cause blockage. The filter needs to be replaced in time. Of course, it is also possible that there are blockages or other parts problems.
Why don't the water dispenser produce water when it powers on normally?
Hello! First, please check whether the the water tank indicator on the display panel is flashing white. If it is flashing, you need to re-install the pure water tank to see if it will be on steadily. Only when the water tank is sensed, the machine will produce water. You can check if the magnet at the bottom of the water tank has fallen off. It may be because of other circuit issues.
Can produce water normally
Water producing and water exchanging indicators are flashing together
You can troubleshoot the following two points:
1、Take out the raw water tank and check whether the float is installed properly.
2, whether the raw water tank cover is covered properly.
Troubleshooting of not producing water
1. If the water shortage light is flashing, first check whether the raw water tank cover is covered properly. Then check whether the raw water tank is installed in place; finally check whether the float is loose or fall off.
2. If the water shortage light does not flash, only the water production light is flashing, first ask the customer if he has disassembled and installed the filter, and then check whether the filter is installed backwards or the filter is not in place.
3. After all the above situations are checked, if the water cannot be produced, please contact us!
Why does the water dispenser stop producing water when the pure water tank is not full?
Customers say that the water dispenser stop producing water suddenly without any water exchanging reminder.
Dear customer, If this problem occurs, you can troubleshoot it by following the steps:
1. Lift the pure water tank and put it back again
2. Unplug the machine, turn it on again, and pour out the water in the pure water tank to produce water again
3. It may because the floating ball of the raw water tank is stuck. You can raw water tank to see if it is normal
PS: After the trouble shooting, you can talk to us about the situation~We will solve it for you.
Loud noise/High decibel
Loud noise when producing water
Dear customer, the decibel measurement by the machine needs to be placed in a professional noise-testing room, at a distance of 1 meter. Generally, the environment in our home is not suitable for direct decibel measurement. It will affect the measured decibel. There will be a little noise when the machine is producing water, which is normal and safe. It is not a product quality problem.
Show malfunctions begin with E, such as E06/EU
Dear customer, This water dispenser shows a fault that starts with E. You can first power off the machine and then power it on again to see if the machine returns to normal. If there is still a problem after the operation, you can contact us to solve the problem for you.
TDS is too high
Dear customer, when this water dispenser shows high TDS, you need to pay attention to the following aspects:
1. When exchanging the water, if the remained water in the water tank is not poured out, the TDS value will increase. It is necessary to pour out the water in the water tank every time the water is changed, and then collect the water.
2. The TDS value is detected based on ambient temperature. If the temperature is too high, the TDS will increase accordingly, which is a normal phenomenon.
3. The amount of water in the water tank also affects the TDS value. The less water, the higher the TDS value. The TDS value will be detected every 60s after producing water. Fluctuations are normal.
4. The TDS value of purified water is related to the water value of your home. The higher the raw water value, the higher the TDS value. Generally, it is safe to drink within 100.
Can the desalinization ratio format be used to calculate whether the TDS on the display panel in the standard? (Customer responses that TDS is high. Can after-sales service calculate by themselves and explain to the customer?)
1. The desalination rate of the RO filter is about 90% (with a normal deviation of ±5)
Desalination rate=[(inlet water TDS - outlet water TDS)/inlet water TDS]*100%
Example: raw water TDS value: 500, purified water TDS value: 50,
Desalination rate=(500-50)/500*100%
=90.00%
Customer uses TDS test pen to test the water from the ADD6926 water dispenser and response that the TDS valve is different. How to explain to the customer?
Can the customer test the water from the dispenser with a TDS test pen? If yes, what are the process and what should be mindful?
the detection value from a TDS test pen and TDS probe will have a certain deviation. When the TDS value of raw water exceeds 100, the deviation is generally about 10%. When the pure water is below 100, the deviation value is about 5%. The deviation is normal. TDS can not be tested with overnight water. Please drain out two tanks of pure water to test after overnight. You can not use hot water to test, which would make the TDS value not precise.
Customer has other RO water dispenser at home. With the same water source, the TDS valve are different between these two dispensers. How to explain this phenomenon?
Dear customer, the RO UTS filtration of other brands has different filter process or material. So the final filtration effect is also different. The drain water from the RO UTS filtration system is directly discharged to the sewer, but the countertop is not. It returns to drain water area of the raw water tank. So the pure water TDS value of the countertop drinking machine will be high in the last few cups of water, which is a normal phenomenon and safe. Don't worry.
What is the calculation logic of TDS test?
TDS actually represents the dissolved solids in water. The detection principle of TDS is to use positive and negative electrodes to form high and low electric fields, so that the ions in the water move in a certain direction of the electric field. And the current flowing through the moving ions forms a certain value, the higher, The more impurities and conductive ions in the water. However, the water quality will affect the accuracy of TDS detection. For example, the water temperature is too high. The same water quality, the higher the temperature, the higher the TDS value will be. Therefore, hot water cannot be used for testing, and it is accurate to use ambient temperature water to test.
When pure the purified water into the raw water tank, the raw water TDS doesn't change. How to explain this phenomenon?
The TDS display value of water in the raw water tank would delay, usually within 3 minutes. The raw water tank needs to be lifted and put back in.
The filter indicator is steady red and the display panel can't operate
Dear customer, when you get this machine, the filter indicator is on red, and the panel cannot be operated. You can press and hold 45°+200ml at the same time to initialize the machine. Restart after power off, and it can return to normal.
There is water in the water dispenser when unboxing
The water dispenser is wet
There are water drops in the water dispenser
This water dispenser needs to be tested randomly with water before sending out from the factory for the product performance. So it is normal for you to receive machine with some water in it. Don't worry.
Inaccurate volume/out of standard
Dear customer, It is normal for this machine to have this problem. There will be a little deviation of the water volume. The deviation range of the water volume is about ±10%, which is a normal situation, not a quality problem of the product. Don't worry.
There is moss in the raw water tank.
Why there will be moss in the raw water tank?
There is moss in the purified water tank.
Dear customer, this situation is caused by the environment of your house. The green algae spores in the air or the green algae spores released by indoor green plants, which enter the water tank with the air. They undergo photosynthesis under the condition of sunlight to multiply. And then form the "moss" that we see. You can place the machine in a place out of direct sunlight, and cleaning the water tank regularly to prevent the growth of moss.
Why the display panel can't operate. There aren't any reactions after I press the buttons.
Dear customer, when the machine has this situation, you can try to power off the machine and restart, to observe it. If this happens again, please contact us.
There is powder in the water. The customers already release water in the raw water tank for 5 times. Why there is still powder?
Dear customer, it is normal for this machine to have this situation. This is the protective liquid of the filter element. Before the filter element is installed in the machine, a layer of glycerin protective liquid will be applied on the surface. This glycerin protection solution is food grade glycerin. It is recommended that you use it with more water and observe it for a few more days.
Can the pure water tank be filled with hot water?
You can put hot water in it.
The filter can't be screwed off?
Please send the filter wrench of ADD6926 to the customer, and use the wrench to unscrew the filter.
ADD6928
Condensate water or water leakage at the bottom of the machine
1. When water appears at the bottom of the machine, touch the hand to check whether the water is cold. The temperature of the bottom refrigeration area is low. When it meets a high temperature and high humidity environment, it is easier to form condensate water collection
2. Check whether the water connecting plate is full, leading to water overflow
3. Lift the water jug to check whether there is damage and cause water leakage
4. Lift the tap water tank to check whether there is damage and cause water leakage
5. Check whether the bottom of the tap water tank and the concentrated water check valve are stuck and cause water leakage
6. Check whether the bottom drain plug is loose and causes water leakage."
The pure water jug indicator is flashing, no filtration
1. Lift the pure water jug and check whether the float at the bottom of the water jug falls off and is missing
Cleaning mode
Click the "clean" button ➡safety lock➡ dispense button and the machine enters clean mode
At this time, will dispense ambient water ➡ hot water, the upper right display 100% complete and flashing, automatically exit the cleaning mode
Operation & care
1. It is suggested that 20cm of cooling space should be reserved behind the machine to facilitate the heat dissipation of the compressor in the machine, so as not to affect the refrigeration efficiency and life of the compressor
2. It is recommended to avoid direct sunlight to prevent the breeding of microorganisms.
1. It is suggested to let the machine stand for 2 hours before enabling the cooling function.
2. After the first use of the new machine or replacing the filter element, it should operate the cleaning mode according to the instructions. (cleaning to 100% is recommended)
3. If not using it for more than a week, or use it continuously for a month, should click on clean button to start the cleaning program.
4. When there is obvious dirt in the water tank or pure water tank, it should be cleaned with cleaning tools and citric acid solution.
5. It is recommended to clean the air filter when the refrigeration time becomes longer and the refrigeration noise becomes larger, or after using for more than half a year.